Holiday @ Jakarta @ Nov 2011

# Syahirah and Syukri are acting infront of Istana Anak2 Indonesia @ Taman Mini Indonesia.

Harimau Malaya return home to heroes' welcome

Harimau Malaya return home to heroes' welcome

Ummu Ammar @ Sumayyah

Ummu Ammar adalah pemilik nama asli Sumayyah binti Khayyath. Beliau adalah ibunda dari Ammar bin Yasir, orang yang bersegera memenuhi seruan Allah SWT dan Rasul-Nya. Nama Sumayyah terdapat pada baris pertama catatan nama-nama perempuan yang mati syahid.


Sumber - The Power of Woman / Gema Insani.

RIPPLE MILL

The ripple mill must incorporate the following design features and performance ;

CRACKING CAPACITY

• 8 TPH to 10 TPH nuts.

RIPPLE ROTOR ROTATIONAL SPEED

• 600 - 700 rpm.

ELECTRIC MOTOR DRIVE

• Minimum 11 KW 4 pole TEFC squirrel cage Brook / Hansen / equivalent motor.

DRIVE

• Belt driven with taper locks for pulleys fitted to both motor and ripple mill shafts.

RIPPLE PLATE

• Easy pull out design.
• Two (2) segments with 12 to 16 teeth per segment.
• Total ripple plate surface area of not less than 2280 cm2.
• Ripple Plate width of 400 mm minimum.

ROTOR ASSEMBLY

• Rotor disc diameter of 650 mm minimum.
• No less than 55 nos. of 25 mm dia. heat treated hardened rotor rods.
• Easy replacement of rotor rods without dismantling of rotor sides plates.
• Rotor shaft dia. of not less than 70 mm.

CRACKING EFFICIENCY

• Able to achieve up to 97% cracking efficiency with broken kernel content less than 10% for wet nuts with moisture content between 14-18%.

NOISE LEVEL

• Between 85-90 dB (A).

VIBRATION LEVEL

• Within 0.7 mm - 1.5 mm RMS vibration velocity in accordance to ISO 2372 Specification for small size machine.

Source - Tender Specification / BEA.

Apply for ISPO cert from Jan 2012

MY palm oil: Apply for ISPO cert from Jan 2012: KUALA LUMPUR: Malaysian oil palm planters in Indonesia, whose estates are mandated to be certified under the Indonesia Sustainable Palm Oil...

10 PERANAN IBU BAPA MENJELANG PEPERIKSAAN

1. Fahami Tekanan Yang Dihadapi Oleh Anak.
2. Tingkatkan Keyakinan Diri Anak.
3. Dorong Anak Secara Positif.
4. Kerjasama Sepenuhnya.
5. Kurangkan Aktiviti Luar.
6. Elakkan Anak Dari Tidur Lewat.
7. Berikan Anak Pelepasan Tugas Harian.
8. Nyatakan Ganjaran Dengan Jelas.
9. Ambil Cuti.
10. Banyakkan Berdoa Dan Solat Hajat.
    

Sumber - Dr. Tengku Asmadi Tengku Mohamad.

6 Cara Mudah Membuat Anak Merasa Disayangi | iluvislam.com + discover the beauty of islam

6 Cara Mudah Membuat Anak Merasa Disayangi | iluvislam.com + discover the beauty of islam

tahniah Syukri

# tahniah Syukri. teruskan usaha. semoga lebih cemerlang dalam UPSR. insyaAllah.

sekadar buat renungan ......

Quote of The Day

"Don't wish it were easier, wish you were better. Don't wish for fewer problems, wish for more skills. Don't wish for less challenges, wish for more wisdom."

- Earl Shoaf

Malaysians at Risk!

SCREW PRESS

Technical Specifications for Screw Press ;

TYPE

• Continuous double scroll screw press for oil palm fruits.

CAPACITY

• Average machine throughput of 23 tonnes FFB per hour at worm screw speed of not exceeding 10 rpm for 500 running hours.

DRIVE

• The squirrel cage motor is to be coupled with a compatible wedge-belt pulley type hydraulic fluid coupling driving a speed-reducer.
• The speed reducer shall be directly connected to the screw press drive shaft via a suitably sized chain type coupling.
• The speed-reducer for the press shall be a Brevini / SEW Eurodrive or approved equivalent unit with a rated output torque of above 48,000 Nm and a reduction ratio of no more than 80:1 and shall have a service factor of 1.6 or better at a press output speed of 10 rpm. The motor shall be 420V 0.8 power factor 50 Hz nominal 1500 rpm and shall not be less than 45 KW for 20 to 25 TPH press.

CAGE & WORM SCREWS

• The press cage shall be of carbon steel material and shall have holes flared from 4mm to 5mm diameters, the smaller diameter being at inside surface of the cage.
• The screw flights shall be of constant pitch.
• The screw-press performance at its rated throughput shall be proven over 500 hours processing its required FFB tonnage.

SHAFTS

• All shafts material used shall be of ASAB 705 high tensile steel shafts or approved equivalent.

MOTORS

• Motor shall be TEFC motor, tropically insulated to Class F, B.S. 2960 or B.S. 3979.
• The drive motor is expected to be not less than 30 KW for 15 TPH press and 45 KW for 20 to 25 TPH press.

POWER HYDRAULICS & PRESSURE CONTROL

• The press shall be equipped with Position Control System, which monitors the pressing pressure (motor current load) and constantly and continuously positioning the press plate to the required pressing pressure. This hydraulic system is designed to auto start upon starting the screw press, and there shall be no pressing load in case if the motor stops as the pressing cone eases off the press cake completely automatically.
• The hydraulic system produces consistent and stable pressing pressure with precise positioning of pressing cone, and has effectively overcome operator dependency.

TEST ON COMPLETION

• Oil loss, less than 7.5% on Non Oily Solids average over 6 continuous hours at rated throughput over three occasions.
• Broken nuts and kernels, less than 8% to total nuts, averaged over 6 hours at rated throughput over three occasions.

Source - Tender Specification / BEA.

Cycling Fever.....

### my children ; Era, Eri and Eqa during morning session of cycling. good and healthy outdoor activity.

teropong.....di mana Ayah

### rupa2nya mereka teropong di mana Ayah. tak cukup korum nak celebrate birthday Eqa. next time Ayah boleh join. insyaAllah. happy birthday Eqa. semoga diberkati Allah selalu.

don't worry .....

happy birthday Nur Syafiqah

### happy 3rd. year birthday to my daughter Nur Syafiqah. may Allah bless you.